Taalman - Products

Products

86 results found!

Case solder-on tank kit

These tanks have 2" diameter hose connections, and steel mounting brackets on each end. The top hank has a filler neck, and the bottom tank has a 1/4" NPT flange for a drain.
individual tanks #4268 and #4269.

#9725 - HDR: 20 1/4" x 4 3/4"

Case solder-on tank kit

The top tank has a 1 3/4" hose connection and a filler neck, and the bottom tank has a 2" diameter hose connection and a 1/4" NPT flange for a drain. There is a mounting boss at each end with a rubber insert.
Individual tanks #4301 and #4302.

#9724 - HDR: 25 1/4" x 4 3/4"

Case solder-on tank kit

These tanks are a mirror image of each other. They have 1 3/4" diameter hose connections, and a mounting boss with a rubber insert on each end.
Individual tanks #4288 and #4289.

#9722 - HDR: 18 1/4" x 3 1/4"

New Holland solder-on kit

These tanks have 1 3/4" diameter hose connections. The top tank has four rubber mounting bosses, and a filler neck. The bottom tank has a steel mounting bracket.

#9721 - HDR: 28 1/2" x 4 3/4"

John Deere solder-on tank kit

The top tank has a 2 1/4" diameter hose connection, a filler neck, and a 1/4" NPT flange for an expansion fitting. The bottom tank has a 2 1/2" diameter hose connection, a 3/4" connection, and a 1/4" NPT flange for a drain. Each tank has a mounting boss with a rubber insert at each end.
Individual tanks #4262 and #4263.

#9720 - HDR: 20 3/8" x 3 3/4"

John Deere solder-on kit

These tanks have 2 1/4" diameter hose connections, and one tank has a steel bracket on the back.
Individual tanks #3070 and #3071.

#9719 - HDR: 16 1/8" x 5"

John Deere kit

These tanks have 2 1/2" diameter hose connections with a 1/4" flange for a drain cock on the bottom tank's connection. There is a steel bracket on the tanks with a clamp reinforcing the hose connections.
Individual tanks #4147 and #4148.

#9718 - HDR: 11 7/8" x 3"

John Deere solder-on tank kit
These tanks have 1 1/2" diameter hose connections. The inlet tank has a 1/4" NPT flange for a drain, and the outlet tank has a filler neck.
Individual tanks #4174 and #4175.

#9713 - HDR: 22 1/4" x 5 1/4"

Case Solder-on Kit

Top Tank
This tank has a 2" diameter hose connection, two mounting bosses with rubber inserts, and a filler neck on the top driver side.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, two mounting bosses with rubber inserts, and a hole for a 1/4" NPT drain cock and flange (supplied).

Individual tanks #4260 and # 4261.

#9712 - HDR: 18 1/8" x 4 3/4"

Case Solder-on Kit

Top Tank
This tank has a 2 1/4" diameter hose connection, two mounting bosses with rubber inserts, and a fill neck attached on top of the hose connection.
Bottom tank
This tank has a 2 1/4" diameter hose connection, two mounting bosses with rubber inserts, and a hole for a 1/4" NPT drain cock and flange (supplied).

Individual tanks #4256 and #4257.

#9711 - HDR: 28 1/8" x 4 3/4"

Case solder-on tank kit

These tanks have 2 1/4" diameter hose connections and steel brackets on the backs. The top tank has a raised filler neck, and the bottom tank has mounting studs. Various 1/4" NPT flanges for drain/expansion fittings.
Individual tanks #4153 and #4154.
Case 7120 Tractor Btm tank steel version #4154SB btm tank

#9710 - HDR: 22 3/4" x 3 3/4"

Case solder-on tank set

Top tank has a 1 3/8" diameter hose connection, and the bottom tank has a 1 1/2" diameter hose connection and a 1/4" NPT flange for a drain. Mounting brackets on each end.
Individual tanks #4163 and #4244.

#9709 / 2104CK - HDR: 20 3/4 X 4 3/4

Case Loader Set - Available in brass (9709) or steel (2104CK)

Top Tank

This tank has a 1 3/4" diameter hose connection (1 3/4" long) 3 3/4" from the edge of the tank to the center of the hose connection, a 1 3/8" diameter pipe facing upward just behind the hose connection to accommodate the fill neck, and four 5/16" NC threaded nuts for the side frames to mount to.

Bottom Tank

This tank has a 2 1/2" diameter hose connection (1 3/4" long) 3 3/4" from the edge of the tank to the center of the hose connection, a 1/4" NPT flange for a drain cock, and four 5/16" NC threaded nuts for the side frames to mount to.

Note: #9709 brass set comes with a #1002 Ford fill neck, and a 1/4" NPT drain cock. With #2104CK steel set the fill neck is sold separately.

Steel Kit #2104CK shown here.

#9708 - HDR: 17 3/4" x 3 3/4"

Case solder-on tank kit

These tanks have 1 1/2" diameter hose connections, a 1/4" NPT flange for a drain/expansion fitting, and mounting brackets on each end.
Individual tanks #4207 and #4208.

#9707 - HDR: 19" x 3 1/4"

Case solder-on kit

These tanks have 2" diameter hose connections, steel brackets that run the length of the tanks, and the bottom tank has a 1/4" NPT flange for a drain. Individual tanks #4104 (top), and #4105 (btm).

#9706 - HDR: 17 3/4" x 3 3/4"

Case solder-on kit

Both tanks in this kit are identical. They have 1 1/2" diameter hose connections, steel mounting brackets at both ends, and a 1/4" NPT flange for drain/expansion fitting. Individual tank #4136.

#9705 - HDR: 25 3/4" x 4 1/2"

John Deere solder-on kit

Top tank has 2 1/4" diameter hose connections and bottom tank is 2 1/2" hose connection, the top tank has a hole for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain on the bottom of the hose connection. Individual tanks #4116 (top), and #4117 (btm).

#9704 - HDR: 20 7/8" x 4 3/4"

Case solder-on kit

The top tank has a 1 3/4" diameter hose connection, and a hole for a filler neck. The bottom tank has a 2 1/4" diameter hose connection, and a flange for a drain cock on the bottom of the hose connection, and a steel bracket that runs the length of the tank. Individual tanks #4119 (top), and #4120 (btm).

#9703 HDR: 22 3/4" x 3 3/4"

Case solder-on kit

These tanks have a 1 1/2" diameter hose connection, a mounting bracket on each end, and the top tank has a 1/4" NPT flange for an expansion fitting. Individual tanks #4121 (top), and #4122 (btm).

#9702 HDR: 13 5/8" x 3 1/4"

John Deere solder-on kit

These tanks have 1" diameter hose connections, the top tank has a hole for a filler neck and a steel bracket, and the bottom tank has a flange for a drain cock. Individual tanks #3076 (top), and 3077 (btm).

#9701 HDR: 21 3/8 x 3 1/4

John Deere solder-on tank kit

These tanks have 2" diameter hose connections. The top tank has steel mounting brackets and a hole for a filler neck, and the bottom tank has a steel mounting bracket that runs the length of the tank and a 1/4" NPT flange for a drain cock. Individual tanks #3074 (top), and #3075 (btm).

#9700 HDR 23 1/8 x 4 1/4

John Deere solder-on tank kit

The top tank has a 2" diameter hose connection, and the bottom tank has a 2 1/8" diameter hose connection. The top tank has four mounting bosses with rubber inserts, a hole for a filler neck, and a 1/2" NPT flange for a sight glass. The bottom tank has a 1/4" NPT flange for a drain on the bottom of the hose connection. Individual tanks #4295 (aka 3047) (top), and #4290 (aka 3048) (btm).
Steel version #080808A.

#4154S - HDR: 28 1/4" x 4 3/4"

Case Tractor solder-on Btm tank

This tank has a 2 1/4" diameter hose connection, a 1/4" NPT flange for a drain fitting, and two 1/2" NC threaded studs @ 14 3/4" centers offset towards the engine.

#4118 - HDR: 21 7/8" x 4 1/4"

Case solder-on tank

This tank has a 2" diameter hose connection, a 1" diameter hose connection, and a 1/4" NPT flange for a hose barb.

#2105CK - HDR: 24 1/4" X 4 3/4"

John Deere/Case solder-on tank set

Top and bottom tanks are identical except for the 1 3/8" diameter fill neck hole on the top tank. There are four pin mounts on each tank for mounting the side frames, and a 2" diameter hose connection 4" from the edge of the tank to the center of the hose connection.

Note: kit comes with eight 5/16" x 6" NC bolts and nuts, and a #1001 GM filler neck.

#2101CK - HDR: 24 3/4" x 4 3/4"

Case Loader

Both tanks in this set are identical. Each has a 1 3/4" diameter hose connection 3 5/8" from the edge of the tank to the center of the hose connection, and four 5/16" NC threaded nuts for mounting the side panels.

#121610A - HDR: 16 1/2" x 4 3/4"

John Deere solder-on tank set

These tanks have 2" diameter hose connections. The top tank has a 1 1/4" diameter hole for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain fitting.

#121207A - HDR: 27 7/8" x 4 3/4"

Case Loader Bottom Tank

This tank has a 2 1/4" diameter hose connection, a 1/4"NPT fitting for a drain cock, a 3/4" diameter bypass hose, and a 14 plate oil cooler with 18" centers and 3/4" NPT fittings (replaces the original 15 plate with metric fittings).

#111711A - LNGTH: 27 1/4" - HDR: 5 1/8" wd. 1" dp.

Case solder-on side frame

This frame has four slotted holes along each edge, and two slotted holes on the back.

#110811B - HDR: 29 2/4" x 4 3/4"

Case solder-on tank

This tank has a 1 3/4" diameter hose connection, 1 1/4" diameter hole for a filler neck.

#102209A - HDR: 16 3/4" x 4 7/8"

John Deere solder-on tank

This tank has a 2 1/2" diameter hose connection, and a 3/8" NPT flange for a drain.

#100808A - HDR: 20 1/8" x 4 7/8"

John Deere bottom tank

This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange for a drain cock.

#092806A - HDR: 22 5/8" X 4 1/8"

Case Loader tank set

Top Tank
This tank has a 1 3/4" diameter hose connection, and a 1 3/8" diameter fill neck hole at the top right.
Bottom Tank
This tank has a 2 1/4" diameter hose connection.

#091610A - HDR: 12 5/8" x 3 3/8" - 8 lbs.

John Deere Gator solder-on complete set

These tanks have 1" diameter hose connections, and the top tank has a 1/8" diameter flange for an expansion fitting.

Side frames are 12 3/8" long, 3 5/8" wide, and the distance between the tanks is 10".

#090110A - HDR: 20 3/4" x 4 3/4"

Case Loader solder-on tank set

These tanks are identical. They have a 2 1/4" diameter hose connection, a 1/4" NPT flange for a drain/expansion fitting, and four 5/16" NC threaded mounting nuts to attach side frames.

#082907A - HDR: 21 7/8" x 5 15/16"

John Deere top tank

This tank has a 2" diameter hose connection that angles downward, and a stand pipe to accommodate a filler neck.

#082808A - HDR: 21 5/8" x 5 1/4"

Case solder-on tank set

These tanks both have a 2" diameter hose connection 3" in length, and a 1/2" NPT flange.

#082411A - HDR: 21 5/8" x 5 1/4"

Case solder-on tank set

Inlet Tank
This tank has a 2" diameter hose connection, a 1/2" NPT flange, and a 1/4" NPT flange.
Outlet Tank
This tank has a 2" diameter hose connection, and a 1/2" NPT flange.

#080808A - HDR:23 3/16" x 4 1/8"

John Deere solder-on tank set

This set matches brass kit #9700.

#080712A - HDR: 18 3/8" x 3 1/2" - 14 lbs

Case solder-on tank set

Top Tank
This tank has a 1 1/2" diameter hose connection 1 3/4" from the edge of the tank to the center of the hose connection, and a 7/8" hole on the top for an import filler neck (part#1005).
Bottom Tank
This tank has a 1 1/2" diameter hose connection in the center of the tank, and a 1/4" NPT flange for a drain fitting on the grill side of the tank.

#080609A - HDR: 21 7/8" x 3 3/8" - 9 lbs.

John Deere tank set

Top Tank
This tank has a 2" diameter hose connection, and 1 1/4" diameter hole for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange for a drain.

#080510A - HDR: 16 1/2" x 4 3/4"

John Deere solder-on tank set

The top tank has a 1 1/2" diameter hose connection and a hole for a filler neck, and the bottom tank has a 1 7/8" diameter hose connection, and a 1/4" NPT flange for a drain fitting on the grill side.

#080411A - HDR: 27 7/8" x 4 3/4"

Case Loader solder-on tank

This tank has a 2 1/4" diameter hose connection 7 1/4" in from the edge of the tank to the center of the hose connection.

#080310A - HDR: 37 3/8" x 5"

John Deere solder-on tank set

These tanks have 2" diameter hose connections. The top tank has a hole for a filler neck, and the bottom tank has three 1/2" NC threaded mounting studs and a 1/4" NPT flange for a drain fitting.

#072310A - HDR: 23 5/8" x 3 7/8"

Case Loader solder-on set

These tanks have a 2 1/2" diameter hose connection. The top tank has a hole for a filler neck and a deflection baffle under the fill hole. The bottom tank has a 1216PC oil cooler and a 1/4" NPT flange for a drain fitting.

#072009A - Mounting Bracket

John Deere mounting bracket

This bracket is designed to fit over the bottom tank of brass kit #9700 (tank #3047), or the bottom tank of the corresponding steel kit #080808A.

There are six 3/8" NC threaded mounting holes, eight 3/8" clearance holes, a cut-out for the hose connection, and a cut-out to access the drain cock.

#071610A - HDR: 28 3/4" x 2 3/4"

Case solder-on tank set

These tanks have 2" diameter hose connections. The top tank has a hole for a filler neck and two 5/16" NC threaded holes on each end to attach side frames, and the bottom tank has a 1/4" NPT coupling for a drain fitting and two mounting pins with 1/4" NC threaded holes in the center.

#071509A - HDR: 21 3/4" x 4 1/4"

John Deere tank set

Top Tank
This tank has a 1 1/2" diameter hose connection that comes out on an angle, four 5/16" NC threaded nuts to attach side frames, a 1 3/8" diameter hole for a filler neck, a 1 3/8" diameter stand pipe for a filler neck (original tank had a screw-cap filler), three 1/4" NPT flanges for a sensor and expansion fittings, and a small surge tank built into the top.
Bottom Tank
This tank has two holes @ 9 1/2" centers for an oil cooler, a 5/8" bypass hose, a 1 3/4" diameter hose connection, a mounting bar running along the center of the tank, and four 5/16" threaded nuts to attach side frames.

#071012A - HDR: 21 1/2" x 4" - 10 lbs

Case solder-on bottom tank

This tank has a 2 1/2" diameter hose connection 2 1/2" from the edge of the tank to the center of the hose connection, and a mounting bracket at each end.

Note: this tank matches with top tank #062207A.

#070809A - HDR: 19 1/2" x 3 1/2"

Case Tractor tank

This tank has a 2" diameter hose connection 4 3/4" in from the edge of the tank to the center of the hose connection.

#063009A - HDR: 16 7/8" x 4 3/4"

John Deere complete rad set

Top Tank
This tank has a 2 1/4" diameter hose connection, a 1 3/8" diameter hole for a filler neck, and a deflection baffle.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange for a drain cock.
Side Frames
These 47 7/16" long by 5 3/8" wide frames have eight 3/8" NC threaded nuts along the edge of the frame, and four 3/8" NC threaded nuts along the opposite edge.

#062612A - HDR: 22 1/2" x 4 3/4" - 10 lbs

John Deere solder-on tank set

These tanks have a 1 1/2" diameter hose connection 5 3/4" from the edge of the tank to the center of the hose connection, four mounting pins tapped 5/16" NC @ approx. 18 3/4" centers to attach side frames.

The top tank has a 1 3/8" stand pipe on the top for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain fitting.

#062212A - HDR: 29 1/2" x 5"

Case Loader solder-on bottom tank

This tank has a 3" diameter hose connection, a 1 1/4" diameter hose connection that bends towards the ground at approx. 80^o, a 1/4" NPT flange for a drain fitting, a 14 plate oil cooler with 18" centers (#1418PC), and a deflection baffle that partially covers the oil cooler.

#062207A - HDR: 21 1/2" X 4"

Case solder-on top tank

This tank has a 2 1/2" diameter hose connection, a 1/2" NPT flange to accommodate a sight glass, and a pair of mounting brackets (one on each end).

This tank matches with bottom tank #071012A.

#061209B - HDR: 16 3/8" x 5 1/4"

John Deere solder-on tank set

Top Tank
This tank has a 2 1/4" diameter hose connection 2" long, and a 1 3/8" diameter hole for a filler neck.
Bottom Tank
This tank has a 2 1/4" diameter hose connection 4" long, and a 1/4" NPT flange for a drain cock.

Note: this is a retrofit, the original tanks were narrower.

#060407A - HDR: 20 3/4" x 4 3/4"

Case solder-on bottom tank - 1994

This tank has a 2 1/4" diameter hose connection 4 1/8" in from the edge of the tank to the center of the hose connection, a 1/4" NPT flange for a drain, and a bracket on each end to mount side frames.

#052912A - HDR: 20 1/8" x 4 7/8"

John Deere solder-on tank set

Top Tank
This tank has a 2 1/4" diameter hose connection, a 1 1/4" diameter hole on the top, and a 1 3/8" diameter hole on the top.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange for a drain fitting.

#051712A - HDR: 20 7/8" x 4 3/4"

Case Tractor solder-on tank set

Top Tank
This tank has a 1 3/4" diameter hose connection 5 1/4" from the edge to the center of the HC, and a hole on the top for a filler neck.
Bottom Tank
This tank has a 2 1/4" diameter hose connection 4 1/2" from the edge to the center of the HC, and a 1/4" NPT flange.

#050409A - HDR: 26 1/8" x 3"

John Deere solder-on tank set

Top Tank
This tank has a 2" diameter hose connection, a hole for a filler neck, and a 1/2" NPT flange for a sight glass.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange for a drain cock.

Note: this set is to replace an original side by side rad and oil cooler - original tanks measured 14" x 3".

#042909A - HDR: 29 1/2" x 6"

Case Dozer bottom tank

This tank has a 2 3/4" diameter hose connection, and a 1/4" NPT flange for a drain cock.

#042711B - HDR: 26 3/4" x 6" - 45 lbs.

Case solder-on tank set

Top Tank
This tank has two 2 1/4" diameter hose connections, a deairation baffle, and a 1 3/4" diameter hole for a fill neck.
Bottom Tank
This tan has a 2 3/4" diameter hose connection, a 1/4" NPT flange for a drain fitting, and a 1418PC plate oil cooler.

#042707B - 16 1/2" x 4 3/4"

John Deere solder-on tank

This tank has a 2" diameter hose connection on the driver's side 2 3/8" from the edge of the tank to the center of the hose connection, and a 1/4" NPT flange on the grill side of the tank 4 3/4" from the edge of the tank.Front and back views shown here.

#041012A - HDR: 26 3/4" x 3 7/8"

Case solder-on tank set

Top Tank
This tank has a 2" diameter hose connection, and a stand pipe for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange on the hose connection for a drain fitting.

#032808A - Shroud

This shroud has been modified as per customer instruction.

#031411A - HDR: 22 1/2" x 4 3/4" - 14 lbs.

Case solder-on tank set

Top Tank
This tank has a 1 3/4" diameter hose connection, four 5/16" NC nuts to attach side frames, and a 1/4" NPT flange for an expansion fitting.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1" diameter bypass connection, four 5/16" NC nuts to attach side frames, and a 1/4" NPT flange on the grill side for a drain fitting.

#031010A - HDR: 22 1/2" x 4 3/4"

Case Tractor solder-on tank set

Top Tank
This tank has a hole for a filler neck, a 1/8" NPT fitting, two 1/4" NC threaded holes on the fan side, a 2 1/4" diameter hose connection, and four 5/16" NC threaded nuts to attach the side frames.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, four 5/16" NC threaded nuts to attach side frames, a 18mm x 1.5mm threaded boss for a sensor, and a 1/4" NPT flange for a drain fitting.

#030512B - HDR: 21 1/2" x 4"

Case solder-on tank set

Top Tank
This tank has a 2 1/2" diameter hose connection, a 1/2" NPT flange for a sight glass, two mounting brackets, and a 1 1/4" diameter hole for a filler neck.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, two mounting brackets, and a 1/4" NPT flange for a drain fitting.

#022411A - HDR: 25 5/8" x 5 7/8"

John Deere 540B Skidder solder-on tank set

Top Tank
This tank has a 2" diameter hose connection, a 1 3/8" diameter hole for a filler neck, and a deflection baffle.
Bottom Tank
This tank has a 2" diameter hose connection, two holes for the oil cooler (one on the grill side and one on the fan side), and a 1/4" NPT flange for a drain fitting on the grill side.

Note: oil cooler must be supplied by the customer.

#022008A - HDR: 21 5/8" x 3 1/2"

John Deere Complete solder-on tank set

Top Tank
This tank has a 2" diameter hose connection 3" from the edge of the tank to the center of the hose connection, and a 1 3/8" diameter hole at the top of the tank for a fill neck.
Bottom Tank
This tank has a 2" diameter hose connection 7" from the edge of the tank to the center of the hose connection, and a 1/4" NPT flange for a drain cock.
Side Frames
These frames have three 3/8" NC threaded mounting nuts along the back of the frame, and eight 3/8" NC threaded mounting nuts along the fan/grill edge (three along one edge, and five along the opposite edge.

#021508A - 24 1/2" x 4 3/8"

John Deere Loader

Top Tank
This tank has a 1 3/4" diameter hose connection 3" from the edge of the tank to the center of the hose connection, two "ears" for lifting the completed unit, and a 1 3/8" diameter hole on the top of the tank for the filler neck.
Bottom Tank
This tank has a 1 3/4" diameter hose connection, a 5 plate 8" center oil cooler (to be provided by the customer), and a 1/4" NPT flange for a drain cock.

#021011A - HDR: 16 1/2" x 4 3/4" - 11 lbs.

John Deere solder-on tank set

These tanks have 2 1/4" diameter hose connections. The top tank has a 1 1/4" diameter hole for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain fitting.

#020811A - HDR: 25 1/2" x 4 3/4" : 12 lbs.

Case Tractor solder-on tank set

Top Tank
This tank has a 1 3/4" diameter hose connection, a 1/4" NPT flange for an expansion fitting, and four 5/16" NC threaded nuts to attach side frames.
Bottom Tank
This tank has 2 1/4" diameter hose connection, a 1" diameter bypass hose, a 1/4" NPT flange for a drain fitting on the grill side, and four 5/16" NC threaded nuts to attach side frames.

#020612A - HDR: 22 7/8" x 4 1/2"

Case solder-on bottom tank

This tank has a 2" diameter hose connection, a 1/4" NPT flange for a drain fitting, a pair of 3/8" NC threaded studs @ 17 3/8" centers (offset towards the grill side), and mounting blocks on each end with two 5/16" threaded holes.

#020609B - HDR: 20 3/4" x 4 3/4"

Case solder-on tank

This Case tank has a 1 5/8" diameter hose connection, and a 1/4" NPT flange.

#020609A - HDR: 22 9/16" x 4 3/4"

Case Tank Set

Top Tank
This tank has a 1 3/4" diameter hose connection, a hole for a filler neck, a 1/4" NPT flange for a sensor, and four 5/16" NC threaded hex nuts to attach the side frames.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, and four 5/16" NC threaded hex nuts to attach the side frames.

#020312A - HDR: 28 1/8" x 4 3/4"

Case Tractor solder-on complete set

Top Tank
This tank has a 2 1/4" diameter hose connection, a 1 3/4" diameter hole for a filler neck, and two 1/4" NPT flanges.
Bottom Tank
This tank has a 2" diameter hose connection, a 1/4" NPT flange for a drain fitting, and a 3/8" NPT flange on the bottom for a second drain fitting.
Side Frames
These frames have four 3/8" NC threaded holes along each edge.

#020212A - HDR: 28 1/4" x 4 3/4"

Case Tractor solder-on tank

This tank has a 2 1/4" diameter hose connection, a 1 3/8" diameter hole for a filler neck, a 1/4" NPT flange, a 1/8" NPT flange, and a bracket with two 1/4" NC threaded nuts.

#020112A - HDR: 25 7/8" x 4 3/8"

Case solder-on tank

This tank has a 1 1/2" diameter hose connection 6" from the edge of the tank to the center of the hose connection.

#012908A - HDR: 27 7/8" x 4 3/4"

Case Loader solder-on top tank

This tank has a 2 1/4" hose connection 7 1/4" from the edge of the tank to the center of the hose connection.

#011609A - HDR: 17 3/4" x 4"

John Deere solder-on tank

This tank has a 1 1/2" diameter hose connection, and a stand pipe
for a filler neck.

Front and back view shown here.

#011409A - HDR: 18 1/8" x 4 3/4"

Case tank set

Top Tank
This tank has a 1 3/4" diameter hose connection, a stand pipe for a filler neck, and four 5/16" NC threaded nuts to attach the side frames.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1/4" NPT flange for a drain cock, and four 5/16" threaded nuts to attach the side frames.

#011107B - HDR: 25 3/4" x 4 7/8"

Case Dozer tank set

Top Tank

This tank has a 2" diameter hose connection 9 1/4" from the edge of the tank to the center of the hose connection, a 1" diameter bypass connection 12 7/8" from the edge of the tank, a 1/4" NPT flange, and a hole on the top of the tank to accommodate a truck style filler neck 2" in from the edge of the tank to the center of the hole.

Bottom Tank

This tank has a 2" diameter hose connection 5" from the edge of the tank to the center of the hose connection, and a 1/4" NPT flange for a drain cock on the other side.

#011012A - HDR: 13 3/4" x 4 11/16"

Case Loader solder-on tank set

These tanks have a 1 3/4" diameter hose connection, and the top tank has a 1 1/4" diameter hole for a filler neck.

#010611B - HDR: 18" x 4 1/4"

Case solder-on set

These tanks have 1 3/4" diameter hose connections and a mounting bracket. The outlet tank has a 7/8" stand pipe for a filler neck.

#010611A - HDR: 23 1/4" x 4 3/4"

Case solder-on tank

This tank has a 2 1/4" diameter hose connection, a 1/4" NPT flange, and two 1/2" NC threaded mounting studs @ 14 3/4" centers.

#010411B - HDR: 17 1/2" x 3 3/8"

Case solder-on tank set

These tanks have 2" diameter hose connections, and a mounting block on each end with two 5/16" NC threaded holes. The top tank has a 1 1/4" diameter hole for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain fitting.