Taalman - Products

Products

20 results found!

#719LF - HDR: 37 1/2" X 6 1/2" - 42 BH - 12 lbs.

Peterbilt bottom tank
This is a blank low flow tank with a 1/4" NPT flange for a drain cock.

Peterbilt bottom tank

This tank has a 3" hose connection, 11 1/2" from the edge of the tank to the center of the hose connection. The connection comes first straight down out of the tank, then bends at 90 degrees to face the engine. This tank is similar to the 7195, except that the hose connection does not sweep upward.

Note: this tank shares the bolt hole pattern with tank #719 and tank #708.

#7198 HDR: 31 1/4" x 6" - 42 BH

Peterbilt bottom tank
This tank has a 2 1/2" hose connection that points downward then angles at 90^o towards the driver side. There is a 1/4" NPT flange at the bottom of the hose connection, and a PTO cutout in the center of the tank.

Note: this tank shares a bolt pattern with tank #511 and tank #800.

#7197 - HDR: 31 1/4" x 6" - 42 BH

Peterbilt bottom tank
This tank has a 2 1/2" hose connection that points downwards then bends at a 90^o angle towards the engine, and a 1/2" NPT flange for a drain cock.

Note: this tank shares a bolt pattern with tank #511 and tank #800.

#7196 - HDR: 31 1/4" x 6" - 42 BH - 8 lbs.

Peterbilt bottom tank
This tank has a 1 1/4" diameter hose connection, and a 3/8" NPT flange. There is a cut-out in the center of the tank to accommodate a PTO.

#7195 - HDR: 37 1/2" x 6 1/2" - 42 BH - 15 lbs.

Peterbilt bottom tank
This tank is similar to tank #719, except the 3" diameter hose connection is curved back and up toward the engine.

#719 - HDR: 37 1/2" X 6 1/2" - 42 BH - 14 lbs

Peterbilt bottom tank
This tank has a 3" diameter hose connection facing to ground.

Note: This tank pairs with top tank #708.

#718LF - 37 1/2" X 6 1/2" - 42 BH - 14 lbs

Peterbilt bottom tank
“Low flow” tank has one 1 1/4" O.D. hose connection on a 90 degree angle facing up and out to passenger side on approximately 45 degree angle. One 1/4" N.P.T. for drain on deep section of tank

#718 - HDR: 37 1/2" X 6 1/2" - 42 BH - 14 lbs

Peterbilt bottom tank
This tank has one bolt-on type flange with four 7/16" NC threaded holes, a 3/8" NPT flange, and two 1/4" NC threaded nuts mounted on the header flange.

#7172 - HDR: 37 1/2" x 6 1/2" - 42 BH

Peterbilt bottom tank

This tank has a 2 1/2" diameter hose connection 15 3/4" from the edge of the tank to the center of the hose connection that comes straight out the bottom of the tank.

Note: bolt pattern is the same as a #719.

#7171 - HDR: 31 1/4" x 6 1/8" - 42 BH

Peterbilt bottom tank

This tank has a 2 1/2" hose connection that comes out at the bottom of the tank then bends 90^o, a 1/4" NPT flange for a drain cock, and a PTO cut-out in the center of the tank.

Note: bolt pattern is the same as a #514 or a #800

#717 - HDR: 30" X 7" - 36 BH - 17 lbs.

Peterbilt bottom tank
Two bolt-on type flanges with two 7/16" N.C. threads in each. One bolt-on type flange with two 5/16" N.C. threads. Two mounting holes with 5/8" N.C. threads at 16" centres. Tank dips in the middle for P.T.O

#716 - HDR: 40 1/2" X 7" - 46 BH - 24 lbs

Peterbilt bottom tank
This tank has two bolt-on type flanges with two 7/16" NC threads in each, a bolt-on type flange on the opposite side in the center with two 5/16" NC threads, and two mounting holes with 5/8" NC threads @ 16" centers.

#715 - HDR: 37 1/2" X 8" - 44 BH - 22 lbs

Peterbilt bottom tank
One bolt-on type flange positioned on a slant with three 3/8" N.C. threads. One bolt-on type flange on opposite side with two 5/16" N.C. threads. Four 1/4" N.C. threaded nuts on header. Two mounting holes with 5/8" threads at 22" centres.

#714 - HDR: 40 1/2" X 7" - 46 BH - 36 lbs

Peterbilt bottom tank
This tank has a bolt-on type flange with four 7/16" NC threaded holes on the front side, a bolt-on type flange with two 5/16" NC threaded holes on the backside, and mounting holes with 5/8" NC threads @ 16" centers.

#713 - HDR: 30" X 8 1/2" - 38 BH - 21 lbs.

Peterbilt bottom tank
This tank has two bolt-on type flanges with two 7/16" NC threaded holes in each, a bolt-on type flange with two 5/16" NC threaded holes on the opposite side, and two mounting holes with 5/8" NC threads @ 16" centers. The center of the tank has a cut-out to accommodate a PTO.

#712 - HDR: 30" X 8 1/2" - 38 BH - 20 lbs

Peterbilt bottom tank
This tank has two bolt-on type flanges with two 7/16" NC threads in each, a bolt-on type flange on the opposite side with two 5/16" NC threads, and two mounting holes with 5/8" NC threads @ 16" centers.

#711 - HDR: 30" X 8 1/2" - 38 BH - 17 lbs.

Peterbilt bottom tank
This tank has a bolt-on type flange on the front with four 7/16" NC threaded holes, a bolt-on type flange on the back with two 5/16" NC threaded holes, and two mounting holes with 5/8" NC threads @ 16" centers.

#710 - HDR: 30" X 7" - 36 BH - 18 lbs

#040510A - HDR: 37 1/2" x 6 1/2" - 42 BH

Peterbilt bottom tank
This tank is similar to tank #7172, except that the hose connection is 3" in diameter and on a slight angle from front to back.