16 results found!
#110310C - CAC Side Frame 
Gillig Bus CAC side frame

This frame is 36 1/8" long by 7 1/4" wide, and 1 1/4" deep.
There are two mounting brackets on the back, eight 3/8" NC nuts and eight 1/4" threaded holes along each edge.
#110310B - LNGTH: 31 1/4" - HDR: 7 5/8" wd. x 6 1/4" dp. 
Gillig Bus side frame

This frame has two mounting brackets on the back, ten 1/4" NC threaded holes along each edge, and two mounting bosses on the gussets to mount cross bars.
#082809A - HDR: 24 1/8" x 7 5/8" - 34 BH 
Gillig Bus bottom tank

This tank has a 3" diameter hose connection, and a 1/4" NPT flange for a drain cock.  Similar to tank #073109G, except the hose connection is centered.

Note:  pairs with top tank #051208A.
#082609A - HDR: 19 5/8" x 9 5/8" - 36 BH 
Gillig Bus top tank

This tank has a 2" diameter hose connection, and two 3/8" NPT flanges on top.
#073109K - Threaded Bar 
Gillig Bus threaded washer bar

This bar has a length of 7 5/8", and has five bolt holes threaded to 5/16" NC.
#073109K - Threaded Bar 
Gillig Bus Washer Bar

This bar has a length of 7 5/8" and has 5 bolt holes.
#073109I - Bracket 
Gillig Bus Bracket

This bracket is made of 14 guage steel and has dimensions of 2 7/8" by 3/4".  There are two bolt holes to attach to the header, and two slotted holes.
#073109H - Washer Bar 
Gillig Bus washer bar

This bar has a total length of 22 1/8" and has 12 bolt holes.
#073109G - HDR: 24 1/8" x 7 5/8" - 34 BH 
Gillig Bus Top tank

This tank has a 3" diameter hose connection that comes down and out on a 90o angle, and a 1/4" NPT flange for a drain cock.

Note:  pairs with top tank #051208A
#073109F - CAC Bracket 
Gillig Bus CAC Bracket

This bracket is 19" long by 7 5/8" wide by 7 1/8" tall.  It has six 3/8" holes to attach frames on one side, five 3/8" holes to attach frames on the cut-out side (cut-out is to accommodate the CAC casting), two 3/4" holes for isolation grommets, and a boss to attach the cross bars.

Shown here with air deflectors installed (sold separately) - part #073109F-1  &  #073109F-2
#073109E - Length: 31 1/4" - HDR: 7 5/8" w. 4 1/2" dp. 
Gillig Bus side frame

This frame has two mounting brackets on the back, two mounting tabs on the edge, two bosses for mounting the cross bars, and six 1/4" NC threaded holes along each edge.
#073109D - Length: 31 1/4" - HDR: 7 5/8" w. 4 1/2" dp. 
Gillig Bus side frame

This frame has four 3/8" NC threaded nuts along each edge of the frame, and four bolt holes at each end.
#073109C - Crossbar 
Gillig Bus cross bar

This is a 3/8" diameter bar with 2" of 3/8" NC threads at each end.  Total length is 48".
#073109B - CAC Bracket 
Gillig Bus CAC Bracket

This bracket is 19" long by 7 5/8" wide by 7 1/8" tall.  It has six 3/8" holes to attach frames on one side, five 3/8" holes to attach frames on the cut-out side (cut-out is to accommodate the CAC casting), two 3/4" holes for isolation grommets, and a boss to attach the cross bars.

Shown here with air deflectors installed (sold separately) - part #073109B-1  &  #073109B-2
#073109A - Length: 33 1/8" - HDR: 7 1/8" w. 1 1/4" dp. 
Gillig Bus CAC side frame

This frame has two mounting brackets on the back, two mounting brackets on the edge, eight 3/8" NC threaded holes and four 1/4" NC threaded holes along each edge.
#051208A - HDR: 24 1/8" x 7 5/8" - 34 BH 
Gillig Bus btm tank

This tank has a 3" diameter hose connection in the front center of the tank, and a 1/4" NPT flange on the top for an expansion fitting.

Note:  pairs with bottom tank #073109G